|
TNP10S, TMP10S(SMD) 20W |
|
Download PDF File |
 |
HOME INTRO HISTORY PRODUCTS NEWS
|
TNP10S, TMP10S(SMD) 20W |
|
Download PDF File |
|
TMP10S(SMD) TNP10S
GENERAL SPECIFICATIONS
|
Test |
Limit |
Condition |
||
|
Rated Power |
20W |
Flange temp. of -55 to 25C |
||
|
Rated Power |
1W |
Free air (no heatsink) |
||
|
Heat Resistance |
5.9C/W |
From hot spot to flange |
||
|
Resistance Range[ohms] |
0.01 -0.09 |
0.1-9.1 |
10-220 |
Up to 51Kohm available, Note 6 |
|
Nominal Resistance |
E6 |
E24 |
E24 |
|
|
TCR [ppm/C] |
+-250(H) |
+-100(A) |
+-50(C) |
Flange Temp. of -55 to 25C |
|
Tolerance |
+-1%, +-5% |
+-1%, +-5% |
+-1% |
|
|
Temperature range |
-55 to 155C |
|
||
|
Withstanding Voltage |
2000VAC |
|
||
|
Load life |
+-[1.0%+0.05ohm] |
25C, 90min. ON, 30min. OFF, 1000hrs. |
||
|
Humidity |
+-[1.0%+0.05ohm] |
60C: 90-95%RH, DC 0.1W, 1000hours |
||
|
Soldering Heat |
+-[1.0%+0.05ohm] |
350+-5C, 3 seconds |
||
|
Solderability |
Over 75% of surface |
230+-5C, 3 seconds |
||
|
Insulation Resistance |
Over 1000Mohm |
Between terminals and flange |
||
|
Vibration |
+-[0.25%+0.05ohm] |
|
||
CONSTRUCTION
DIMENSIONS
|
|
|
|
mm |
+-mm |
|
|
A |
8.5 |
+-0.2 |
|
|
|
B |
12.0 |
+-0.2 |
|
|
|
C |
3.1 |
+-0.2 |
|
|
|
D |
3.1 |
+-0.1 |
|
|
|
E |
17.0 |
+-1.0 |
|
|
|
F |
3.2 |
+-0.5 |
|
|
|
G |
3.8 |
+-0.2 |
|
|
|
H |
1.75 |
+-0.1 |
|
|
|
J |
0.5 |
+-0.05 |
|
|
|
K |
0.6 |
+-0.05 |
|
|
|
L |
1.4 |
+-0.05 |
|
|
|
M |
5.08 |
+-0.1 |
DERATING CURVE AND TEMPERATURE RISE
 |
 |
NOTES
1/
Insulating material will not be used between flange and
resistors, because flange and
resistor are separated by an alumina substratUsing heat conduction grease
on the surface
of the flange is recommended.
2/
Heat resistance between resistor and flange is 3.6K/W,
attention to thermal design should
be observed as the resistor temperature should be kept under 155C in
operation.
3/
0.1% tolerance resistors are available, please enquire.
4/
For RF application circuits, lead formed TNP10S--Z10(smd) can be prepared,
TNP10S---Z10
are screw mount style.
5/
At resistances from 220 to 51kohms power rating
shall be restricted in 10W.
6/
Standard packaging is RoHS PS/PE tube packaging,
which contains 50pcs/tube. When
ordering, noting tube or tray type packaging is recommended.
ORDERING
PROCEDURE EXAMPLE
Copyright©, RARA Electronics Corporation
Tel:82-32-817-4325 Fax:82-32-817-4329
